SOPs & Documents

GMP 1 — Reading Turning Points GMP 1 – 2019 Page 1 of 2 This publication is available free of charge from: https://doi.org/10.6028/NIST.IR.6969 - 201 9 GMP 1 Good Measurement Practice for Reading Turning Points on an Equal -Arm Balance The damping of the beam oscillation... GMP 2 pages May 2019 GMP 2 — Reading the Center of Graduations When Using a Microscope October 2014 GMP 2 Page 1 of 2 GMP 2 Good Measurement Practice for Reading the Center of Graduations when using a Microscope 1. The microscope furnished to State laboratories with the length bench has a reticle on which each graduation repr... GMP 2 pages 2014 GMP 3 — Reading Meniscus GMP 3 – 2019 Page 1 of 7 This publication is available free of charge from: https://doi.org/10.6028/NIST.IR.7383 - 2019 GMP 3 Good Measurement Practice for Method of Reading a Meniscus Using Water or Other Wetting Liquid 1 Meniscus Reading... GMP 8 pages May 2019 GMP 4 — Adjusting the Optical Scale on a Single Pan Mechanical Balance GMP 1 pages 1986 GMP 5 — Weight Cleaning Procedures GMP 6 pages 1986 GMP 6 — Cleaning Metal Volume Measures GMP 6 – 2019 Page 1 of 2 This publication is available free of charge from: https://doi.org /10.6028/NIST.IR.7383 - 2019 GMP 6 Good Measurement Practice for Cleaning Metal Volumetric Measures 1 Cleanliness requirements All volumetric test m... GMP 2 pages May 2019 GMP 7 — Cleaning Precision Glassware GMP 7 – 2019 Page 1 of 3 This publication is available free of charge from: https://doi.org/10.6028/NIST.IR.7383 - 2019 GMP 7 Good Measurement Practice for Cleaning Precision Glassware 1 Cleanliness requirements The volume contained in or d... GMP 4 pages May 2019 GMP 8 — Recommended Form of Reporting Tape Calibrations October 2014 GMP 8 Page 1 of 4 GMP 8 Good Measurement Practice for Reporting Tape Calibrations Tape calibration results should be reported as described in SOP 1, Preparation of Calibration Certificates. The use of the Calibration Certificat... GMP 4 pages 2014 GMP 9 — Equations for Metallic Tapes October 2014 GMP 9 Page 1 of 2 GMP 9 Good Measurement Practice for Equations for Metallic Tapes Table 1. Symbols used in this practice. Symbol Description L Horizontal straight-line distance LS Calibrated length of the tape interval on a fl... GMP 2 pages 2014 GMP 10 — Weighing Operation Factors GMP 10 – 2019 Page 1 of 6 This publication is available free of charge from: https://doi.org/10.6028/NIST.IR.6969 - 201 9 GMP 10 Good Measurement Practice for Understanding Factors Affecting Weighing Operations Good laboratory techniques an... GMP 6 pages May 2019 GMP 11 — Calibration Intervals GMP 11 – 2019 Page 1 of 9 This publication is available free of charge from: https://doi.org/10.6028/NIST.IR.6969 - 201 9 GMP 11 Good Measurement Practice for Assignment and Adjustment of Calibration Intervals for Laboratory Standards 1 Int... GMP 10 pages May 2019 GMP 12 — Selecting Sops GMP 12 – 2019 Page 1 of 4 This publication is available free of charge from: https://doi.org /10.6028/NIST.IR .6969 - 201 9 GMP 12 Good Measurement Practice for Standard Operating Procedure Selection Good laboratory practices, use of proper... GMP 4 pages May 2019 GMP 13 — Ensuring Traceability GMP 13 – 2019 Page 1 of 17 This publication is available free of charge from: https://doi.org/10.6028/NIST.IR.6969 - 2019 GMP 13 Good Measurement Practice for Ensuring Metrological Traceability 1 1 Introduction Purpose The purpose of this G... GMP 17 pages Jun 2019